Compatible Replacement Parts for Sandvik-Family Cone Crushers

Coverage across the Sandvik family

The Sandvik-family hydrocone design — hydraulic setting adjustment and chamber clearing on a compact frame — is installed across quarrying and mining worldwide. Our compatible programme addresses the family at brand level, against model and part number — and only at brand level: the catalogue records no individual part lines against Sandvik-family models, so this page publishes no coverage list for the family, neither chamber wear parts nor mechanical spares. Send the model and the original part number, and the enquiry is answered line by line: supply from the general catalogue against that part number, supply against drawing, or an honest no. No part line is recorded against Symons machines either, and the recorded lines behind HP machines stand against their HP sizes only, and the only GP-series records in the catalogue are the GP220 upper frame and the GP220 top bearing, recorded against the GP220 only; every line for those machines, as for this family, is confirmed against its own model and part number.

Chamber liners for hydrocone duty

Hydrocone chambers run fine and extra-fine duties where product shape is sold by specification, so liner profile accuracy matters commercially, not just mechanically. Across our wear programme, mantles and concaves are profiled manganese castings, and the matched-set recommendation applies: chamber geometry is a pair property. For a Sandvik-family machine, a liner is proposed only after the model, chamber and original part number have been checked — no mantle or concave line is recorded against this family, against the HP sizes, against the GP series or against Symons machines. The guidance in when to replace mantle and concave was written for exactly the setting-drift symptoms hydrocone operators notice first in their product grading.

Identification discipline

Sandvik-family parts are identified by model, chamber and original part number. Similar-looking liners across chamber variants are the classic mis-order in this family; a part number check before casting is cheaper than a shutdown spent discovering the difference. Send the part number from the liner itself or the manual, plus the chamber designation, and the quotation will state the exact compatible part proposed. Dimensioned photographs resolve cases where documentation is incomplete.

Ordering

Minimum order is 1 piece on a confirmed line, confirmed with your quotation, which suits the trial-liner approach: once a set has been confirmed against your model and part number, run it in one crusher, compare life and product against the incumbent, then decide on fleet supply with your own data. Lead time is confirmed per quotation, typically within 15 workdays in peak season for common lines and around one month off-season. Shipment on FOB, EXW, CIF or FCA terms; payment by T/T or L/C. Certificates available upon request. Plants running Sandvik-family cones alongside HP or Symons machines can consolidate all compatible parts into one enquiry and one shipment — with no part line recorded against this family in that shipment either — the recorded lines in the catalogue stand against specific HP sizes (bowls, head assemblies, gears, main frames and clamping rings) and against the GP220 (the upper frame and the top bearing) only, and no part line is recorded against Symons machines either — so each part in the shipment is confirmed against its own machine's model and part number. The mantles and concaves discussed on this page are not recorded against the HP sizes, against the GP series or against Symons machines either — for those machines, as for this family, each liner is confirmed against its model and original part number when quoted.

Trial discipline: proving a compatible liner in your own chamber

Once a liner set has been confirmed against a Sandvik-family model and part number, the rational way to adopt it across the fleet is a controlled trial, and this programme is set up to make trials cheap to run. The trial liner set is not recorded against the HP sizes, the GP series, Symons machines or this family — it is confirmed against your model and part number like every line here. Order one set — the minimum order is a single piece or set, confirmed with the quotation — for one crusher, in the chamber profile that machine runs. Before fitting, record the incumbent set's final data: tonnes achieved, product gradation at the standard setting, and the wear pattern. Fit the trial set as a matched pair, hold feed and setting policy constant, and measure the same three numbers at removal. The comparison is then your own plant's arithmetic, not a supplier's brochure: life in tonnes, product held to specification, cost per tonne. If the trial wins, extending supply across the fleet reuses the proven identification data, so every subsequent order is a repeat, not a new experiment. If it does not win, the wear record will show where — and that record is exactly what a grade or profile correction is built from.